The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system

Margo Pujiantara; Dedet Candra Riawan; Aditya Indrasaputra; Talitha Puspita Sari; Vincentius Raki Mahindara

doi:10.1109/ICPERE.2018.8739673

The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system

Margo Pujiantara
, Dedet Candra Riawan
, Aditya Indrasaputra
, Talitha Puspita Sari
, Vincentius Raki Mahindara

Institut Teknologi Sepuluh Nopember

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

4 Citations (Scopus)

Abstract

A radial or ring distribution system is mostly used in industrial application with electrical components that are very complex and require a lot of attention in terms of the protection coordination of the electrical system. In the coordination of Over Current Relay (OCR), the setting is usually obtained by trial and error which is very subjective and time consuming. Therefore, a new program based on numerical computation algorithm is proposed, specifically to facilitate the calculation of Time Dial Setting (TDS) and the selection of the Time-Current Characteristic (TCC) curve for setting the inverse over current relay on the real electrical system. The main objective of this paper is to get the setting value of OCR easily but with an accurate result. The result shows that the proposed program is able to have a close result with the existing value in real electrical system and even comes with the recommendation regarding the TDS and curve selection.

Original language	English
Title of host publication	4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings
Publisher	Institute of Electrical and Electronics Engineers Inc.
ISBN (Electronic)	9781538674567
DOIs	https://doi.org/10.1109/ICPERE.2018.8739673
Publication status	Published - Oct 2018
Event	4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Solo, Indonesia Duration: 29 Oct 2018 → 31 Oct 2018

Publication series

Name	4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings

Conference

Conference	4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018
Country/Territory	Indonesia
City	Solo
Period	29/10/18 → 31/10/18

UN SDGs

This output contributes to the following UN Sustainable Development Goals (SDGs)

SDG 7 Affordable and Clean Energy

Keywords

Numerical computation
Over current relay
Protection coordination
Time-current characteristic curve

Access to Document

10.1109/ICPERE.2018.8739673

Cite this

Pujiantara, M., Riawan, D. C., Indrasaputra, A., Sari, T. P., & Raki Mahindara, V. (2018). The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system. In 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings Article 8739673 (4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings). Institute of Electrical and Electronics Engineers Inc.. https://doi.org/10.1109/ICPERE.2018.8739673

Pujiantara, Margo ; Riawan, Dedet Candra ; Indrasaputra, Aditya et al. / The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system. 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings. Institute of Electrical and Electronics Engineers Inc., 2018. (4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings).

@inproceedings{94a25bfe8a614f7d946e1774587a69b4,

title = "The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system",

abstract = "A radial or ring distribution system is mostly used in industrial application with electrical components that are very complex and require a lot of attention in terms of the protection coordination of the electrical system. In the coordination of Over Current Relay (OCR), the setting is usually obtained by trial and error which is very subjective and time consuming. Therefore, a new program based on numerical computation algorithm is proposed, specifically to facilitate the calculation of Time Dial Setting (TDS) and the selection of the Time-Current Characteristic (TCC) curve for setting the inverse over current relay on the real electrical system. The main objective of this paper is to get the setting value of OCR easily but with an accurate result. The result shows that the proposed program is able to have a close result with the existing value in real electrical system and even comes with the recommendation regarding the TDS and curve selection.",

keywords = "Numerical computation, Over current relay, Protection coordination, Time-current characteristic curve",

author = "Margo Pujiantara and Riawan, \{Dedet Candra\} and Aditya Indrasaputra and Sari, \{Talitha Puspita\} and \{Raki Mahindara\}, Vincentius",

note = "Publisher Copyright: {\textcopyright} 2018 IEEE.; 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 ; Conference date: 29-10-2018 Through 31-10-2018",

year = "2018",

month = oct,

doi = "10.1109/ICPERE.2018.8739673",

language = "English",

series = "4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings",

publisher = "Institute of Electrical and Electronics Engineers Inc.",

booktitle = "4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings",

address = "United States",

}

Pujiantara, M , Riawan, DC, Indrasaputra, A, Sari, TP & Raki Mahindara, V 2018, The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system. in 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings., 8739673, 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings, Institute of Electrical and Electronics Engineers Inc., 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018, Solo, Indonesia, 29/10/18. https://doi.org/10.1109/ICPERE.2018.8739673

The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system. / Pujiantara, Margo ; Riawan, Dedet Candra; Indrasaputra, Aditya et al.
4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings. Institute of Electrical and Electronics Engineers Inc., 2018. 8739673 (4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

TY - GEN

T1 - The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system

AU - Pujiantara, Margo

AU - Riawan, Dedet Candra

AU - Indrasaputra, Aditya

AU - Sari, Talitha Puspita

AU - Raki Mahindara, Vincentius

PY - 2018/10

Y1 - 2018/10

N2 - A radial or ring distribution system is mostly used in industrial application with electrical components that are very complex and require a lot of attention in terms of the protection coordination of the electrical system. In the coordination of Over Current Relay (OCR), the setting is usually obtained by trial and error which is very subjective and time consuming. Therefore, a new program based on numerical computation algorithm is proposed, specifically to facilitate the calculation of Time Dial Setting (TDS) and the selection of the Time-Current Characteristic (TCC) curve for setting the inverse over current relay on the real electrical system. The main objective of this paper is to get the setting value of OCR easily but with an accurate result. The result shows that the proposed program is able to have a close result with the existing value in real electrical system and even comes with the recommendation regarding the TDS and curve selection.

AB - A radial or ring distribution system is mostly used in industrial application with electrical components that are very complex and require a lot of attention in terms of the protection coordination of the electrical system. In the coordination of Over Current Relay (OCR), the setting is usually obtained by trial and error which is very subjective and time consuming. Therefore, a new program based on numerical computation algorithm is proposed, specifically to facilitate the calculation of Time Dial Setting (TDS) and the selection of the Time-Current Characteristic (TCC) curve for setting the inverse over current relay on the real electrical system. The main objective of this paper is to get the setting value of OCR easily but with an accurate result. The result shows that the proposed program is able to have a close result with the existing value in real electrical system and even comes with the recommendation regarding the TDS and curve selection.

KW - Numerical computation

KW - Over current relay

KW - Protection coordination

KW - Time-current characteristic curve

UR - https://www.scopus.com/pages/publications/85068549829

U2 - 10.1109/ICPERE.2018.8739673

DO - 10.1109/ICPERE.2018.8739673

M3 - Conference contribution

AN - SCOPUS:85068549829

T3 - 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings

BT - 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings

PB - Institute of Electrical and Electronics Engineers Inc.

T2 - 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018

Y2 - 29 October 2018 through 31 October 2018

ER -

Pujiantara M , Riawan DC, Indrasaputra A, Sari TP, Raki Mahindara V. The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system. In 4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings. Institute of Electrical and Electronics Engineers Inc. 2018. 8739673. (4th IEEE Conference on Power Engineering and Renewable Energy, ICPERE 2018 - Proceedings). doi: 10.1109/ICPERE.2018.8739673

The automation of time dial setting calculation and inverse type curve selection for over current relay based on numerical computation in real industrial electrical system

Abstract

Publication series

Conference

UN SDGs

Keywords

Access to Document

Other files and links

Fingerprint

Cite this